Water Specialties
Propeller Meters |
- PROPELLER METERS
- Flanged Tube
- Top Plate Assemblies
- Saddle
|
TRANSMITTERS
|
|
| ML03 |
Downloads |
|
MODEL ML03 FLANGED TUBE METERS are manufactured to the highest
standards. Materials used on all meters and flow ranges for the low
velocity meter meet or exceed AWWA standard C704-02. The flanged
end tube design permits use in a wide range of applications with up
to 150 psi working pressure. Flanged ends are 150 lb. AWWA class D
flat face steel flanges. Fabricated steel meter tubes have straightening
vanes and are protected internally and externally with 12-15 mils of
NSF approved, fusion bonded epoxy resin. |
 |
 |
|
| ML04 | Downloads |
|
MODEL ML04 FLANGED TUBE METERS are manufactured to the highest standards. Materials used on all meters and flow ranges for the low velocity meter meet or exceed AWWA standard C704-02. The flanged end tube design permits use in a wide range of applications with up to 150 psi working pressure. Flanged ends are 150 lb. AWWA class D flat face steel flanges. Fabricated steel meter tubes have straightening vanes and are protected internally and externally with 12-15 mils of NSF approved fusion epoxy resin. |
|
|
|
| ML-I1 | Downloads |
|
MODEL MLI1 METER HEAD ASSEMBLIES are manufactured to the
highest standards. Materials used on all meters and flow ranges
for the low velocity meter meet or exceed AWWA standard C704-
02. The bolt-on design permits use in a wide range of applications
with up to 150 psi working pressure. It is necessary, upon ordering,
to furnish the meter size, model number and serial number of the
meter it is replacing. |
|
|
|
| ML-I1X | Downloads |
|
MODEL MLI1X METER HEAD ASSEMBLIES are manufactured to the highest
standards. Materials used on all meters and flow ranges for the low
velocity meter meet or exceed AWWA standard C704-02. The bolt-on
design permits use in a wide range of existing applications with up to
150 psi working pressure. It is necessary, upon ordering, to furnish the
I.D. dimension of the pipe the meter is to be mounted on for calibration
purposes, and the saddle dimensions from the back of the data sheet. It
may be necessary to modify or remove the existing straightening vanes
to allow proper clearance for Water Specialties three bladed propeller (see
propeller dimension on back of data sheet). |
|
|
|
| ML-T1 | Downloads |
|
MODEL MLT1 METER HEAD ASSEMBLIES are manufactured to the
highest standards. Materials used on all meters and flow ranges for
the low velocity meter meet or exceed AWWA standard C704-02. The
bolt-on design permits use in a wide range of existing applications
with up to 150 psi working pressure. It is necessary, upon ordering, to
furnish the meter size, model number and serial number of the meter
it is replacing. |
|
|
|
| ML-T1X | Downloads |
|
MODEL MLT1X METER HEAD ASSEMBLIES are manufactured to the
highest standards. Materials used on all meters and flow ranges for
the low velocity meter meet or exceed AWWA standard C704-02. The
bolt-on design permits use in a wide range of existing applications with
up to 150 psi working pressure. It is necessary, upon ordering, to
furnish the I.D. dimension of the pipe the meter is to be mounted on
for calibration purposes, and the saddle dimensions from the back of
the data sheet. It may be necessary to modify or remove the existing
straightening vanes to allow proper clearance for Water Specialties three
bladed propeller (see propeller dimension on back of data sheet). |
|
|
|
| LP-21 | Downloads |
|
MODEL MLT1X METER HEAD ASSEMBLIES are manufactured to the
highest standards. Materials used on all meters and flow ranges for
the low velocity meter meet or exceed AWWA standard C704-02. The
bolt-on design permits use in a wide range of existing applications with
up to 150 psi working pressure. It is necessary, upon ordering, to
furnish the I.D. dimension of the pipe the meter is to be mounted on
for calibration purposes, and the saddle dimensions from the back of
the data sheet. It may be necessary to modify or remove the existing
straightening vanes to allow proper clearance for Water Specialties three
bladed propeller (see propeller dimension on back of data sheet). |
|
|
|
| ML19, ML20, ML20D |
Downloads |
|
MODEL ML19, ML20, ML20D WELD-ON SADDLE METERS Materials used on all meters and flow ranges for the low velocity
meter meet or exceed AWWA standard C704-02.The weld-on design
permits use in a wide range of applications with up to 150 psi working
pressure. It is necessary, upon ordering, to furnish the I.D. dimension
of the pipe the meter is to be mounted on for calibration purposes. The
O.D. dimension or wall thickness must also be furnished for proper fit of
the saddle to the pipe. |
|
|
|
| LP-22 | Downloads |
|
MODEL LP22 STRAP-ON SADDLE METERS are designed for irrigation or
other low pressure service up to 150 PSI working pressure. The strapon
design permits installation on many types of pipe material (3/16"
PVC wall minimum). It is necessary upon ordering to furnish the I.D.
dimension of the pipe the meter is to be mounted on, for calibration
purposes. The pipe O.D. dimension must be 4.50" for proper sealing
of the saddle to the pipe. |
|
|
|
| LP-31 | Downloads |
|
MODEL LP31 STRAP-ON SADDLE METERS are designed for irrigation or
other low pressure service up to 150 PSI working pressure. The stainless
steel saddle (brass 4") and u-straps permit installation on a wide
range of steel, cast-iron, plastic (3/16" PVC wall minimum), asbestos,
and other pipe materials for each nominal meter size. It is necessary
upon ordering to furnish the I.D. dimension of the pipe the meter is to
mounted on, for calibration purposes. The pipe O.D. dimension (20"
max.) or wall thickness must also be furnished for proper sizing of the
U-straps. NOTE: Consult factory for O.D. larger than 20". |
|
|
|
| LP-32 | Downloads |
|
MODEL LP32 STRAP-ON SADDLE METERS are designed for irrigation or other
low pressure service up to 150 PSI working pressure. The stainless steel
saddle and u-straps permit installation on a wide range of steel, cast-iron,
plastic (3/16" PVC wall minimum), asbestos, and other pipe materials
for each nominal meter size. It is necessary upon ordering to furnish
the I.D. dimension of the pipe the meter is to mounted on, for calibration
purposes. The pipe O.D. dimension (20" max.) or wall thickness must also
be furnished for proper sizing of the U-straps. NOTE: Consult factory for
O.D. larger than 20". |
|
|
|
| VF27 |
Downloads |
|
MODEL VF27 VERTICAL UPFLOW METERS are designed to meet
AWWA specifications. The bolt-on design permits use in a wide
range of applications with up to 150 psi working pressure. The
mounting flange conforms to ANSI class 125 drilling. It is necessary,
upon ordering, to furnish the I.D. dimension of the pipe the meter is
to be mounted on for calibration purposes. |
|
|
|
| TR01-1 | Downloads |
|
MODEL TR01-1 TOTALIZER-TRANSMITTERS provide a totalization of flow volume and a pulse rate output signal proportional to the rate of flow when mounted on our meters. The unit features a magnetically driven totalizer, and solid state construction. |
|
|
|
| TR06-1 | Downloads |
|
MODEL TR06-1 INDICATOR-TOTALIZER-TRANSMITTERS provide an instantaneous flow rate indication, a totalization of flow volume and a pulse rate output signal proportional to the rate of flow when mounted on our propeller meters. The unit features a mechanically driven indicator-
totalizer, and solid state construction. |
|
| |
|
| TR12-2 | Downloads |
|
MODEL TR12-2 INDICATOR-TOTALIZER-TRANSMITTERS provide an instantaneous flow rate indication, a totalization of flow volume and a pulse rate output signal of one contact per totalizer hand revolution when mounted on any of our propeller meters. The unit features a durable magnetically actuated reed switch. |
|
|
|
| TR15 | Downloads |
|
MODEL TR15 TOTALIZER-TRANSMITTERS provide a totalization of flow volume and both a 4-20 mA current signal and a pulse rate output signal proportional to the rate of flow when mounted on our meters. The unit features a magnetically driven totalizer, and solid state construction. |
|
|
|
| TR16 | Downloads |
|
MODEL TR16 INDICATOR-TOTALIZER-TRANSMITTERS provide an instantaneous
flow rate indication, a totalization of flow volume and both a 4-20 mA current signal and a pulse rate output signal proportional to the rate of flow when mounted on our propeller meters. The unit features a mechanically driven indicator-totalizer, and solid state construction. |
|
|
|
